Car Audio Electronics
For Your Convenience and Comfort
Car Audio Electronics | Blaupunkt Car Stereo | Car Stereo MP3 | Car Stereo System | Online Car Stereo

/Pyle-PLTS77DU-Monitor-Receiver Pioneer-Fh-P8000Bt-Wav-Receiver Polk-Audio-DB651-6.5-Inch-coaxial-Speakers

Car Stereo System

Should you be on a limited budget but want a more rewarding sound system inside your vehicle, set up a stereo on your own! Putting in a new radio or CD player inside your car is straightforward for anyone with any experience cabling. This informative guide clarifies step-by-step how to install a head unit into the dash of your automobile.

Do the Necessary Preparations

Step 1

Buy a new stereo system. Ensure that you get one that will match correctly into the slot for your old one. Furthermore, when purchasing a new car stereo system you could probably get a cabling harness that's specific to both your vehicle's make and model as well as the brand new music system. Purchase one of these if you're able to since it will make the cabling in no time!

Step 2

Get hold of these tools and materials: electrical tape, wire cutters, wire strippers, and screwdrivers.

Step 3

You will probably want a guide to be able to remove the dash panel of your car that demonstrates the way to correctly get rid of your old radio.

Getting rid of your Old Music system

Step 1

Detach the ground (negative) wire from your battery. In no way work on the electrical system of your vehicle with this connected.

Step 2

Take out the dash panel that covers your music system. Unscrew and slide out the unwanted head device. Challenging either be a single plug with many different cables that connects to the back of it or a variety of individual cables. In the event that there are lots of individual cables going straight into the back of the unit don't remove them yet because you'll want to do them one-by-one to avoid confusion.

Step 3

Plug the connector directly into your new cabling harness, in case your were capable of getting such a harness for your car or truck. This harness must then be connected directly into the back of your new music. In the event you did this you may omit the next section.

Do the Wiring Manually

Step 1

Hook up each wire on your own in case your were not able to obtain a wiring harness to set up the car stereo.

Step 2

Hook up the positive cable from each speaker to the positive connector on the backside of the stereo system first. After that hook up the negative wire from each speaker to the negative connector on the backside of the stereo system. If you find just one cable coming from the speakers, the actual speakers are grounded at the framework. In this instance you need to set up new speaker cabling.

Step 3

Hook up the ground (-/black) cable of the stereo system to a screw or bolt close to the place that the radio is mounted within the dash. Make certain the cable is attached to metal, and definitely not plastic material or fiberglass.

Step 4

Hook up the 12 constant and ignition power wires (both /red) to your new stereo system. Refer to your stereo's set up guide to be sure these go to the right places.

Inserting the Car Stereo system.

Step 1

Now you really should have a good single connector that hooks to all the right cables in your vehicle, either from the cabling harness you bought or the one that was included with your stereo system that you have currently attached all the suitable cables to.

Step 2

Slide your new head unit into the mounting bracket that was included with it. In some unusual cases you may have to make use of the bracket from your previous car stereo.

Step 3

Connect the harness connector in to the backside of the new stereo system. There should be just one lone cable left from your old stereo system now. This is actually the antenna. Plug this into your new device. There may be a power antenna cable in addition that you will have to connect.

Step 4

Slide your new car stereo system into the slot inside the dash. Do not screw it in yet; you will need to test it first.

Step 5

Reunite the negative wire of your car to the battery.

Step 6

Switch your vehicle on and power up your new stereo. Put some music on and listen to all of your loudspeakers to ensure everything functions properly.

Step 7

Screw your new car stereo unit into the corect position then put the dash cover back on.

Click Here for more product information.

·	Car Audio Electronics

·	Products
·	About Us

·	Contact Us

·	Privacy Policy

·	Site Map